How to fold Origami : Japanese crane

origami crane instruction  :

1. Start with a square piece of paper, coloured side up. Fold the top corner of the paper down to the bottom corner. Crease and open again. Then fold the paper in half sideways.	2. Turn the paper over to the white side. Fold the paper in half, crease well and open, and then fold again in the other direction.

3. Using the creases you have made, Bring the top 3 corners of the model down to the bottom corner. Flatten model.

4. Fold top triangular flaps into the centre and unfold	5. Fold top of model downwards, crease well and unfold

6. Open the uppermost flap of the model, bringing it upwards and pressing the sides of the model inwards at the same time. Flatten down, creasing well.

7. Turn model over and repeat Steps 4-6 on the other side.	8. Fold top flaps into the centre.

9. Repeat on other side, so your model looks like this.	10. Fold both ‘legs’ of model up, crease very well, then unfold.

11. Inside Reverse Fold the “legs” along the creases you just made.	12. Inside Reverse Fold one side to make a head, then fold down the wings

Finished Crane!

                            

Origami lucky star instructions

origami lucky star instruction :

1. Start with a strip of paper. Tie a “knot” in the end of your paper.	2. Pull gently to tighten, then flatten.

3. Fold the end of the strip down and tuck it into the knot. You can cut a bit of it off if it's too long.	4. Now wrap the other end of the strip around and around this pentagon you have formed, creasing gently as you go.

5. Keep wrapping until you get to the end of the strip. Tuck the last bit of the strip into the pouch. You should be left with a cute little pentagon.	6. Now to make this little pentagon into a star, very gently and slowly use your fingernail to press on the centre of each of its edges. The star should puff out.

And you should have a lovely little lucky star! It may take some practise to get the star to puff out perfectly, but stick with it... you’ll get it! If you are having a lot of trouble, try different papers, or try wrapping the strip of paper around without creasing it too much. This helps a bit!

Origami Pandora's Box (Yami Yamauchi)

origami pandora box instruction :

          

           

How to Make an Origami Butterfly

origami butterfly instuction :

1. Start with your paper white side up. Fold in half, open, then fold in half the other way.	2. Now Fold the Paper in half diagonally, both ways.	3. Fold all four corners into the centre and crease well.

4. Turn Over and Fold all four corners into the centre again.	5. Open out the model so far. Your creases should look like this. It looks complicated, but dont worry!

6. Fold the outside edges into the centre line.	7. Holding each inside edge from the point at the centre, bring these edges out to the points shown. Then, fold the top edge downwards and flatten.

8. Rotate the model, and repeat step 7.

9. Fold the top half backwards and flatten.	10. Fold down the front outside corners.	11. Fold these outside corners inward as shown.

12. Fold the butterfly in half.	13. Now fold the top layer backwards, at the angle shown.	14. And now fold the back wing backwards also at the same angle

15. Open out.	Your butterfly is complete!

Origami: Elephant

origami  elephant  intructions :

 
                 
           
               

Rose origami (daftar putar)

origami rose instruction  :

   

1. Make these creases. 2. Form the 4 corners. 3. Flatten, while rotating counter-clockwise. 4. Turn over. 5. Form the 3D rose by taking each top right corner and folding to next quadrant, counter clockwise. 6. Form rose within the palm of your hand. 7. Turn over and smooth inside of rose, by pressing down slightly at the base. 8. Fold down edges and tuck in to form the bottom of the rose. 9. Turn over, open centre of flower and smooth. 10. Roll the petals down to curve them. Finished rose.